QUICK START GUIDE
Item #1001318516
1001311061
Model #DFI-5985-BZ
DFI-5985-WH
MOTION SECURITY LIGHT
This guide is not comprehensive. It shows a common installation. For complete information and instructions, download the PDF of the owner’s manual
at www.homedepot.com.
PLANNING INSTALLATION
Before installing the light xture, ensure that all parts are present (see Hardware Included and Package Contents). If any part is missing or damaged, do
not attempt to assemble, install, or operate this light xture.
Estimated installation time: 30 minutes
TOOLS REQUIRED
Phillips screwdriver Flathead screwdriver Wire strippers/cutters Circuit tester Mobile device
Work gloves Silicone sealant Ladder Safety goggles
HARDWARE INCLUDED
AA BB CC
DD EE
FF
FRONT
GG HH
PACKAGE CONTENTS
Part Description Quantity
AA Rubber plug 1
BB Small mounting bolt 1
CC Mounting bracket screw 2
DD Mounting bracket screw 2
EE Mounting bracket screw 2
FF Large mounting bolt (pre-installed) 1
GG Mounting bracket (not to scale) 1
HH Mini screwdriver (not to scale) 1
Part Description Quantity
A Lamp head 2
B Light xture 1
C Motion sensor 1
D
1-2- asy Connect™
1
Questions, problems, missing parts? Before returning to the store,
call Deant Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-866-308-3976
HOMEDEPOT.COM
Installation
1
Installing the mounting bracket
WARNING: Turn the power off at the circuit breaker or fuse. Place tape over the
circuit breaker switch and verify power is off at the light xture.
□ Remove the existing light xture.
□ Install the mounting bracket (GG) with the stamped word “FRONT”
facing away from the junction box. Use the mounting bracket
screws (CC, DD, or EE) that best t the junction box.
FRON T
2
Installing the 1-2- asy Connect™
□ Remove the 1-2- asy Connect™ (D) from the rear of the light
xture.
□ Route the junction box wires through the large hole in the
1-2- asy Connect™ (D).
□ Place the 1-2- asy Connect™ (D) against the junction box.
□ When mounting to a wall, the “UP” arrow must point upward.
□ When mounting to an eave, the “UP” arrow must point toward
the building.
□ Insert the small mounting bolt (BB) through the 1-2- asy
Connect™ (D) hole located below the threaded hole, and thread it
into the center hole of the mounting bracket (GG). Tighten the bolt
(BB) securely.
FRONT
N (White/
Blanc/Blanco)
GND
Terre
Tierra
UP/Haut/Arriba
L (Black/
Noir/Negro)
FRO NT
N (White/
Blanc/Blanco)
GND
Terre
Tierra
UP/Haut/Arriba
L (Black/
Noir/Negro)
3
Making the electrical connections
□ Insert the junction box wires into the side of the terminal block
and around the ground screw. Tighten terminal block screws
using the mini-screwdriver (HH) and ground screw to secure the
wires.
□ Insert the white wire from the junction box into the terminal
marked “N (White)”.
□ Insert the black wire from the junction box into the terminal
marked “L (Black)”.
□ Connect the bare or green ground wire from the junction box
to the ground screw (marked with “GND”).
N (White/
Blanc/Blanco)
GND
Terre
Tierra
UP/Haut/Arriba
L (Black/
Noir/Negro)
4
Mounting the light fixture
NOTICE: The two pins on the rear of the light xture must be inserted into the terminal
block for the light to work.
□ Align the bottom edge of the light xture (B) with the bottom edge
of the 1-2- asy Connect™ (D) and tilt the light xture (B) toward the
1-2- asy Connect™ (D). Ensure the light xture (B) is centered on the
1-2- asy Connect™ (D).
□ Tighten the large mounting bolt (FF) securely through the center
of the 1-2- asy Connect™ (D). Do not overtighten.
□ Push the rubber plug (AA) rmly into the mounting bolt hole on
the light xture (B).
CC, DD, or EE
GG
HOMEDEPOT.com Please contact 1-866-308-3976 for further assistance.
C
A
D
B
FF
AA
D
B
D
D
BB
GG
207907-03A
IMPORTANT:
READ BEFORE
INSTALLATION
Comments to this Manuals